Jump to content



Fordwiki infobox
  • Ford Model: Mondeo Mk2 (1996-2000)
  • Petrol/Diesel: Petrol & Diesel
  • Time Taken? NA
  • Estimated Cost? £0
  • Difficulty?

  • Submitted On: 18 February 2014
  • Last Updated: 18 February 2014
  • Views: 5535
  • Tags:
Page Tools:

  • You cannot edit this guide








  • Headlamp beam deflectors

    Submitted by TalkFord , Feb 18 2014 12:15 PM | Last updated Feb 18 2014 12:15 PM
    Mk2
    The Mk2 instructions are reversible. The headlamp pictures are for a LHD vehicle, so look at your screen in a mirror for RHD. The templates are for nearside and offside, and should be flipped over as appropriate (striped side out on LHD, in on RHD).

    Nearside

    Attached Image: Lhd-lhl2-1.jpg
    Attached Image: Nst2-2.jpg

    Offside

    Attached Image: Lhd-rhl2-3.jpg
    Attached Image: Ost2-4.jpg

    Mk3 - halogen headlamps only

    RHD, RH lamp


    Attached Image: Rhd-rhl-5.jpg
    Attached Image: Rhd-rht-6.jpg

    RHD, LH lamp

    Attached Image: Rhd-lhl-7.jpg
    Attached Image: Rhd-lht-8.jpg

    LHD, RH lamp

    Attached Image: Lhd-rhl-9.jpg
    Attached Image: Lhd-rht-10.jpg

    LHD, LH lamp

    Attached Image: Lhd-lhl-11.jpg
    Attached Image: Lhd-lht-12.jpg

    Mk3 - Xenon (HID) headlamps only
    • Open bonnet.
    • Remove the front grille by twisting the 2 turnknobs.
    • Remove the headlamps from the car by lifting the 2 release levers and disconnecting the elec. connector.
    • Remove the rear cover from the lamp, by removing the 2 screws and pulling up the locking tab.
    • Turn the bulb alignment lever to the required position: Normal position "0" for the UK, or Travel position "T" for driving in continental Europe.
    • Replace the rear cover.
    • Refit the headlamps and front grille.
    • It is recommended to have the headlamp alignment checked after this procedure.
    Alternatively, if you are not inclined to carry out this work, or not prepared to pay a garage to do so, headlamps can be masked using 'Eurolites' masking stickers available in motoring accessory shops.

    Mk4

    Without cornering lamps

    X should be 100mm: adjust scaling as appropriate. The clear bit of the template is a guide; the shaded bit is the mask itself.

    RHD, RH lamp

    Attached Image: Rhrl4-13.jpg
    Attached Image: Rhrt4-14.jpg

    RHD, LH lamp

    Attached Image: Rhll4-15.jpg
    Attached Image: Rhlt4-16.jpg

    LHD, RH lamp

    Attached Image: Lhrl4-17.jpg
    Attached Image: Lhrt4-18.jpg

    LHD, LH lamp

    Attached Image: Lhll4-19.jpg
    Attached Image: Lhlt4-20.jpg

    With cornering lamps
    • Remove the headlamps from the car.
    • Remove the rear cover from the lamps.
    Attached Image: Mk4-headlamp-21.jpg
    • Move the lever behind up or down to adjust the beam as appropriate.
    Attached Image: Mk4-headlamp-lever-22.jpg
    Attached Image: Mk4-headlamp-lever-23.jpg
    • Replace the rear cover.
    • Refit the headlamps.