Jump to content


TalkFord Gold Members Don't See Adverts! Subscribe Today To Hide This Advert!

News Feed (View All Updates)




Photo

P132B fault code


This topic has been archived. This means that you cannot reply to this topic.
5 replies to this topic

#1 Adi69

Adi69

    MEG Sergeant

  • Members
  • 1614 posts

Posted 06 August 2007 - 11:50 AM

Hi,

Following the engine management light coming on the other day, I had the car checked for fault codes.
P132B....with no other letters was one that came up. Has anyone come across this before?

#2 rasman81

rasman81

    Big Megger

  • Members
  • 243 posts

Posted 06 August 2007 - 04:16 PM

I thought that 132 was an o2 sensor high voltage, but the diesel does not have o2 sensors as far as i'm aware.
Kevin
2004 Ghia X Estate


Previously, ST24 Hatch, ST200 Estate

#3 ScoobyChris

ScoobyChris

    MEG Corporal

  • Members
  • 1207 posts

Posted 06 August 2007 - 06:34 PM

I did a Google and turned up this excellent site: http://www.fordtechs...-releaseHL1.pdf

which seems to suggest a possible sticking turbo....


Question:
What is the new P132B code?
Answer:
P132B is a new P-code that was added to monitor turbocharger performance. There are 3 new PIDs
that indicate what operating mode the code was set in, these are:
⇒ P132B_STK sets during the learn mode
o Verify that the turbocharger learn has successfully completed VGTVP_LE > 5 and
VGTVP_OK = yes and check the learned values to make sure that they are within a
correct range
o Run through the normal KA test to verify the turbocharger is actually sticking
⇒ P132B_CM is a continuous monitor
o Verify that the turbocharger learn has successfully completed VGTVP_LE > 5 and
VGTVP_OK = yes and check the learned values to make sure that they are within a
correct range
o Run through the normal KA test to verify the turbocharger is actually sticking
⇒ P132B_VAR sets if the turbocharger does not converge
All turbochargers must be tested through the KA test to verify improper operation.

Chris
Colorado Red '02 Mk3 Ghia-X TDCi (130bhp) - ummmm standard-ish ;)

#4 Adi69

Adi69

    MEG Sergeant

  • Members
  • 1614 posts

Posted 06 August 2007 - 06:55 PM

Thanks for looking Chris.

I too did a Google and found:

http://www.fordinsta...hatsnew/DTL.pdf

If you look at pages 16-19, then along with code P600A which was there too....it shows all the possibilites.

The EGR has been fully cleaned out using a sonic cleaner, it is now fully closing, which is wasn't before. The memory has been cleared and I'll have to see if it returns.

#5 look8one

look8one

    Little Megger

  • Members
  • 8 posts

Posted 16 February 2009 - 04:43 AM

clean the MAF sensor with Electrical solvent cleaner (maplin) Be carefull with two termistors they are easy to damage. It helped me and cost only 4 quid! yes! reg
04reg Zetec S 130bhp 6speed PLATINUM

#6 Adi69

Adi69

    MEG Sergeant

  • Members
  • 1614 posts

Posted 16 February 2009 - 01:48 PM

Well done for sorting yours matey. My car was constantly coming up with P123B which is turbo performance and when manually operating the turbo vanes, they were indeed sticking. I also watched the vanes stick one day when turning off the engine.
I have previously cleaned the MAF as well